8/26/2023 0 Comments Chevy trax 2018 specsPushed into the steering knuckle and the pinch bolt for the lower ball joint can be torqued down to 22 ft-lbs and then an additional 35 degree turn. Towards the front side of the vehicle can be torqued down to 85 ft-lbs and then an additional 65 degree turn. Once tightened you can torque the single rearward frame bolt to 118 ft-lbs and then an additional 35 degree turn. Once remove you can remove the old control arm from the vehicle and then place the new part in the location of the old one and hand tighten up theįrame bolts. Which hold the lower control arm to the vehicle frame and then the single pinch bolt which holds the ball joint to the steering knuckle. To do this you will need to remove the 2 bolts You will need to remove the entire lower control arm along with the lower ball joint. In order to remove the lower ball joint on this vehicle The Chevy Trax has one front ball joint being the lower ball joint. Is the center axle nut which tightens down to 37 ft-lbs plus an additional 60 degree turn.Ĭhevy Trax Front Axle Nut Torque Spec : 37 ft-lbs + 60° All that is left now before reinstalling the braking system and tire Finally the outer tie rodĬan be installed and tightened down to 22 ft-lbs plus an additional 130 degree turn. Inserted into the steering knuckle and the pinch bolt can be tightened down to 22 ft-lbs plus an additional 35 degree turn. When installing be sure to tighten up the lower strut bolts to 82 ft-lbs. The steering knuckle can then be reinstalled onto the vehicle by doing The old hub can be pressed out and the new hub pressed in. ![]() Now you will need to use a press or pressing tool in order to remove hubįrom the knuckle. The old steering knuckle and hub should be removable from the vehicle. Next the outer tie rod nut can be removed and then the center axle nut which hold the cv axle to the steering knuckle. Staring with the 2 bolts which hold the strut to the knuckle and then moving to the lower ball joint This can be done by loosing up the upper and To achieve this you must first remove the steering knuckle from the vehicle. The front wheel hub on the Chevy Trax gets pressed into the steering knuckle and will need to be pressed out in order to beĬhanged. The torque specs for the inner tie rod are 65 ft-lbs.Ĭhevy Trax Outer Tie Rod Torque Spec : 22 ft-lbs + 130°Ĭhevy Trax Inner Tie Rod Torque Spec : 65 ft-lbs Installing the inner tie rod as well you will need a special tool to loosen and tighten Be sure to tightenīack up the nut on the middle of the tie rod to ensure it does not move your alignment. Once you get the nut back in place you can torque it to 22 ft-lbs plus an additional 130 degree turn. Once the outer tie rod is off you can now screw on the new part and reinstall it the same way it had been This helps to avoidĪlignment costs and hassles, although you may still want to get your vehicle realigned. It takes to come off so that I can then use the same number when installing the new part. To hold the inner tie rod and spin off the outer tie rod. ![]() If you want to replace just the outer portion of the tie rod you can use a wrench Once removed you can now tap out the tie rod from the spindle and You may also use a wire brush to clean off the threads prior to removal and or use penatrating oil toĪid in the removal. I suggest using a pair of vice grips to hold the portion of the bolt to prevent it from The inner part of the tie rod uses an nut that will need to be removed, this nut may spin depending on how Once the tire is off you can now access the old tie rod and remove it for replacement. Once the vehicle is in the air you can remove the corresponding tire for the side that you want to change the ![]() This can beĭone by raising the vehicle up by either the use of a floor jack or a vehicle hoist. To install a new tie rod on a Chevy Trax you must first remove the old one from the vehicle.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |